|
Hogging
Cutterheads and Trimming Saw Blades
For use on double end tenoners as scoring and
cut-off saws. With square teeth. For machining
abrasive composite materials, the diamond version
is a preferred
tool.
|
Item#
|
|
Diameter
|
Kerf
|
Bore
|
#
of Teeth |
Tip
Version |
2031.180.30
|
|
180mm |
3.2mm |
30mm |
30 |
carbide |
2031.200.30
|
|
200mm |
3.2mm |
30mm |
34 |
carbide |
2032.150.40
|
|
150mm |
3.2mm |
40mm |
30 |
carbide |
2032.180.30
|
|
180mm |
3.2mm |
30mm |
36 |
carbide |
2032.200.30
|
|
200mm |
3.2mm |
30mm |
42 |
carbide |
2033.150.30
|
|
150mm |
3.2mm |
30mm |
36 |
carbide |
2033.150.40
|
|
150mm |
3.2mm |
40mm |
36 |
carbide |
2033.180.30
|
|
180mm |
3.2mm |
30mm |
42 |
carbide |
2033.181.50
|
|
180mm |
3.2mm |
50mm 3/22/80
|
48 |
carbide |
2033.200.30
|
|
200mm |
3.2mm |
30mm |
48 |
carbide |
2034.150.40
|
|
150mm |
3.2mm |
40mm |
48 |
carbide |
2034.180.30
|
|
180mm |
3.2mm |
30mm |
56 |
carbide |
2034.200.30
|
|
200mm |
3.2mm |
30mm |
64 |
carbide |
7.31.180.30
|
|
180mm |
3.2mm |
30mm |
30 |
PCD/Diamond
|
7.31.200.30
|
|
200mm |
3.2mm |
30mm |
34 |
PCD/Diamond
|
7.32.150.40
|
|
150mm |
3.2mm |
40mm |
30 |
PCD/Diamond
|
7.32.180.30
|
|
180mm |
3.2mm |
30mm |
36 |
PCD/Diamond
|
7.32.200.30
|
|
200mm |
3.2mm |
30mm |
42 |
PCD/Diamond
|
7.33.150.30
|
|
150mm |
3.2mm |
30mm |
36 |
PCD/Diamond
|
7.33.150.40
|
|
150mm |
3.2mm |
40mm |
36 |
PCD/Diamond
|
7.33.180.30
|
|
180mm |
3.2mm |
30mm |
42 |
PCD/Diamond
|
7.33.181.50
|
|
180mm |
3.2mm |
50mm 3/22/80
|
48 |
PCD/Diamond
|
7.33.200.30
|
|
200mm |
3.2mm |
30mm |
48 |
PCD/Diamond
|
7.34.150.40
|
|
150mm |
3.2mm |
40mm |
48 |
PCD/Diamond
|
7.34.180.30
|
|
180mm |
3.2mm |
30mm |
56 |
PCD/Diamond
|
7.34.200.30
|
|
200mm |
3.2mm |
30mm |
64 |
PCD/Diamond
|
|
 |
Small Hogging Set 200mm Diameter
Hardened and precision ground mounting sleeve, suits any make of machine. |
Item# |
|
Description |
|
| |
|
Hogging Width 22mm |
Diameter |
| |
|
Teeth of trimming saw Z42 |
|
2610.200.42 |
|
LH Hogging Set |
200mm |
2610.201.42 |
|
RH Hogging Set |
200mm |
| |
|
|
|
| |
|
Teeth of trimming saw Z60 |
|
2610.202.60 |
|
LH Hogging Set |
200mm |
2610.203.60 |
|
RH Hogging Set |
200mm |
| |
|
|
|
| |
|
|
|
| |
|
Hogging Width 40mm |
|
| |
|
Teeth of trimming saw Z42 |
|
2610.204.42 |
|
LH Hogging Set |
200mm |
2610.205.42 |
|
RH Hogging Set |
200mm |
| |
|
|
|
| |
|
Teeth of trimming saw Z60 |
|
2610.206.60 |
|
LH Hogging Set |
200mm |
2610.207.60 |
|
RH Hogging Set |
200mm |
| |
|
|
|
| |
|
|
|
| |
|
Hogging Width 58mm |
|
| |
|
Teeth of trimming saw Z42 |
|
2610.208.42 |
|
LH Hogging Set |
200mm |
2610.209.42 |
|
RH Hogging Set |
200mm |
| |
|
|
|
| |
|
Teeth of trimming saw Z60 |
|
2610.210.60 |
|
LH Hogging Set |
200mm |
2610.211.60 |
|
RH Hogging Set |
200mm |
| |
|
|
|
| |
|
Recommended RPM: 8000 max |
|
 |
Mounting Sleeve For 200mm Hogging Sets
Hardened and precision ground with cover. Special locking nuts can be supplied as well. |
Item# |
|
L = mm |
d = mm |
keyway |
Machine |
2625.250.00 |
|
91 |
35 |
10x4 |
B&G |
2625.251.00 |
|
75 |
35 |
10x4 |
Celaschi |
2625.252.00 |
|
106 |
35 |
10x4 |
Danckaert |
2625.253.00 |
|
85 |
35 |
10x4 |
Festo |
2625.254.01 |
|
86 |
40 |
12x4 |
Gabbiani |
2625.254.02 |
|
97 |
40 |
12x4 |
|
2625.254.03 |
|
109 |
40 |
12x4 |
|
2625.254.04 |
|
122 |
40 |
12x4 |
|
2625.255.00 |
|
85 |
35 |
10x4 |
Homag |
2625.257.00 |
|
76 |
35 |
10x4 |
Hullhorst |
2625.266.00 |
|
102 |
35 |
10x4 |
Kombina |
2625.258.00 |
|
134 |
35 |
10x4 |
Kuhlmann |
2625.260.00 |
|
104 |
40 |
12x4 |
M&S |
2625.260.01 |
|
106 |
40 |
12x4 |
SCM |
2625.261.00 |
|
100 |
35 |
10x4 |
Spanevello |
2625.263.00 |
|
106 |
35 |
10x4 |
Torwegge, IMA |
2625.264.00 |
|
80 |
30 |
8x4 |
Wadkin |
2625.265.00 |
|
87 |
35 |
|
Wigo |
| |
|
|
|
|
|
| |
Sleeves for 250mm Hogging Set |
|
|
|
|
2625.267.00 |
|
For hogging Set 250 |
|
|
Homag |
2625.268.00 |
|
For hogging Set 250 |
|
|
IMA-Klessmann |
|
 |
Spares for 200mm Hogging Sets
Trimming saw 205 x 4.0 x 100mm with countersink fixing holes for GUHDO Number 2610 hogging cutterheads. |
Item# |
|
Diameter |
kerf |
Bore |
Teeth/Rotation |
Tooth Form |
Hogger Brand |
2630.200.42 |
|
205mm |
4mm |
100mm |
Z 42 LH |
flat |
GUHDO |
2630.201.42 |
|
205mm |
4mm |
100mm |
Z 42 RH |
flat |
GUHDO |
2630.202.42 |
|
205mm |
4mm |
100mm |
Z 42 LH |
single bevel |
GUHDO |
2630.203.42 |
|
205mm |
4mm |
100mm |
Z 42 RH |
single bevel |
GUHDO |
2630.200.60 |
|
205mm |
4mm |
100mm |
Z 60 LH |
flat |
GUHDO |
2630.201.60 |
|
205mm |
4mm |
100mm |
Z 60 RH |
flat |
GUHDO |
2630.202.60 |
|
205mm |
4mm |
100mm |
Z 60 LH |
single bevel |
GUHDO |
2630.203.60 |
|
205mm |
4mm |
100mm |
Z 60 RH |
single bevel |
GUHDO |
| |
|
|
|
|
|
|
|
2630.200.84 |
|
200mm |
4mm |
80mm |
Z 40 LH |
flat |
LEUCO |
2630.201.84 |
|
200mm |
4mm |
80mm |
Z 40 RH |
flat |
LEUCO |
2630.200.86 |
|
200mm |
4mm |
80mm |
Z 60 LH |
flat |
LEUCO |
2630.201.86 |
|
200mm |
4mm |
80mm |
Z 60 RH |
flat |
LEUCO |
| |
|
|
|
|
|
|
|
| |
|
segments for 200mm hoggers |
|
|
|
|
|
2630.200.09 |
|
Z2x9 LH |
|
|
|
|
|
2630.201.09 |
|
Z2x9 RH |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
steel cutterhead body with bolts |
|
|
|
|
|
2630.200.00 |
|
LH |
|
|
|
|
|
2630.201.00 |
|
RH |
|
|
|
|
|
2630.200.50 |
|
Packet of screws |
|
|
|
|
|
|
 |
Hogging Sets 250-335 Diameter
Technical Details: Body of steel with two segments and trimming saw which is precisely centered into a polished flange on the cutterhead body.
Special Features: Hoggers remove the material outwards from the cut panel edge (twice during each revolution) by the two segments being diagonally set in the cutterhead body. The cutterhead body is flush on its workpiece side with a deep recess to accept the spindle and locking nut of the machine. This means that the cutterhead can be operated very close to the chain drive of the machine and consequently cut vibration to a minimum. This also means that thicker panels can be processed with smaller diameter hogging sets, these can even be set to cut through the center of the hogger. This can be an advantage should mitering cuts be necessary by tilting the machine spindle. Another advantage of the recess in the center of the cutterhead is to reduce the weight of the body thus reducing the power requirement when starting and minimizing undue wear on the bearings of the machine. Our popular 280mm diameter hoggers give an ideal feed rate and finish to all laminated panels when running at 6000rpm. |
LH Item# |
RH Item# |
|
Diameter |
Hogging Width |
Bore |
Teeth |
Segments |
2650.250.42 |
2650.251.42 |
|
250mm |
25mm |
60mm |
42 |
2x10 |
2650.250.60 |
2650.251.60 |
|
250mm |
25mm |
60mm |
60 |
2x10 |
2650.252.42 |
2650.253.42 |
|
250mm |
25mm |
80mm |
42 |
2x10 |
2650.252.60 |
2650.253.60 |
|
250mm |
25mm |
80mm |
60 |
2x10 |
| |
|
|
|
|
|
|
|
2650.280.42 |
2650.281.42 |
|
280mm |
30mm |
60mm |
42 |
2x12 |
2650.280.60 |
2650.281.60 |
|
280mm |
30mm |
60mm |
60 |
2x12 |
2650.282.42 |
2650.283.42 |
|
280mm |
30mm |
80mm |
42 |
2x12 |
2650.282.60 |
2650.283.60 |
|
280mm |
30mm |
80mm |
60 |
2x12 |
| |
|
|
|
|
|
|
|
2650.335.60 |
2650.336.60 |
|
335mm |
33mm |
60mm |
60 |
2x16 |
2650.337.60 |
3650.338.60 |
|
335mm |
45mm |
60mm |
60 |
2x16 |
| |
|
|
|
|
|
|
|
| |
For Leuco Quick Change system with 192mm flange |
|
|
|
|
|
|
2651.252.42 |
2651.253.42 |
|
250mm |
25mm |
80mm |
42 |
2x10 |
2651.252.60 |
2651.253.60 |
|
250mm |
25mm |
80mm |
60 |
2x10 |
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
|
|
Recommended RPM: |
|
|
|
| |
|
|
|
D=250mm 6,000 |
|
|
| |
|
|
|
D=280mm 6,000 |
|
|
| |
|
|
|
D=335mm 3,000 |
|
|
| |
|
|
|
|
|
|
|
| |
Trimming Saws with countersunk mounting holes |
|
|
|
|
|
|
LH Item# |
RH Item# |
|
Diameter |
Kerf |
Bore |
Teeth |
Tooh Config. |
2660.250.42 |
2660.251.42 |
|
250mm |
4.0mm |
130mm |
42 |
Flat |
2660.252.42 |
2660.253.42 |
|
250mm |
4.0mm |
130mm |
42 |
Single Bevel |
2660.250.60 |
2660.251.60 |
|
250mm |
4.0mm |
130mm |
60 |
Flat |
2660.252.60 |
2660.253.60 |
|
250mm |
4.0mm |
130mm |
60 |
Single Bevel |
2660.280.42 |
2660.281.42 |
|
280mm |
4.0mm |
170mm |
42 |
Flat |
2660.282.42 |
2660.283.42 |
|
280mm |
4.0mm |
170mm |
42 |
Single Bevel |
2660.280.60 |
2660.281.60 |
|
280mm |
4.0mm |
170mm |
60 |
Flat |
2660.282.60 |
2660.283.60 |
|
280mm |
4.0mm |
170mm |
60 |
Single Bevel |
2660.335.60 |
2660.336.60 |
|
335mm |
4.0mm |
230mm |
60 |
Flat |
| |
|
|
|
|
|
|
|
Trimming Saw for LEUCO quick change system |
|
|
|
|
|
|
|
2660.221.60 |
2660.220.60 |
|
220mm |
4.0mm |
80mm |
60 |
Flat |
2660.250.48 |
2660.251.48 |
|
250mm |
4.0mm |
80mm |
48 |
Flat |
2660.252.48 |
2660.253.48 |
|
250mm |
4.0mm |
100mm |
48 |
Flat |
2660.250.72 |
2660.251.72 |
|
250mm |
4.0mm |
80mm |
72 |
Flat |
2660.252.72 |
2660.253.72 |
|
250mm |
4.0mm |
100mm |
72 |
Flat |
| |
|
|
|
|
|
|
|
Segments |
|
|
|
|
|
|
|
2660.250.10 |
|
|
245mm |
|
|
2x10 |
|
2660.280.12 |
|
|
275mm |
|
|
2x12 |
|
2660.335.16 |
|
|
330mm |
|
|
2x16 |
|
2660.202.09 |
|
|
200/250 |
|
|
4 |
|
| |
|
|
|
|
|
|
|
Steel Cutterhead body with bolts |
|
|
|
|
|
|
|
2660.250.06 |
2660.251.06 |
|
250mm |
25mm |
60mm |
|
|
2660.250.08 |
2600.251.06 |
|
250mm |
25mm |
80mm |
|
|
2660.280.06 |
2660.281.06 |
|
280mm |
30mm |
60mm |
|
|
2660.280.08 |
2660.281.08 |
|
280mm |
30mm |
80mm |
|
|
2660.335.33 |
2660.336.33 |
|
335mm |
33mm |
60mm |
|
|
2660.335.45 |
2660.336.45 |
|
335mm |
45mm |
60mm |
|
|
| |
|
|
|
|
|
|
|
| |
Steel body for Leuco Quick Change System |
|
|
|
|
|
|
2661.251.08 |
|
|
250mm |
25mm |
|
Buy Online
